Ring Roller Mill

An Industrial Ring Roller Mill for Ultrafine Mineral Powder

In this application, a ring roller mill is an industrial dry-grinding system for mineral powder production. Material passes between multiple rollers and stationary grinding rings, where repeated compression, impact, and friction reduce particle size. An air classifier then separates acceptable fine powder from coarse particles that require another pass.

The HGM system is intended for brittle, nonflammable, and nonexplosive materials with a Mohs hardness of 6 or less and moisture content of 6% or less. These boundaries make it suitable for many nonmetallic minerals while also defining when material testing or a different grinding route is necessary.

Closed-circuit classification gives the operator a practical way to control the product cut point. Adjusting the classifier changes which particles leave the circuit, while the mill continues grinding the rejected fraction. This relationship between grinding and classification matters more than a nominal mesh label when the finished powder must meet a repeatable particle-size specification.

Where the value comes from

• Repeated grinding in a compact chamber: Multiple roller-and-ring contact zones keep material moving through successive size-reduction stages.
• Coarse-particle return: The classifier sends oversize powder back to the mill instead of allowing it into the finished product.
• Integrated powder handling: Feeding, grinding, classifying, collecting, filtering, and electrical control can be configured as one production line.
• Scalable HGM platform: Ring diameter, roller count, drive power, classifier arrangement, and line footprint change across the model range.

How Ring-Roller Grinding and Air Classification Work Together

1. Metered feeding and distribution

Raw material is crushed to the required feed size, lifted to a storage hopper, and metered into the mill. A controlled feeder stabilizes the material flow before the rotating distribution plate directs it toward the grinding chambers.

2. Multi-layer roller-and-ring grinding

The main drive rotates the internal assembly so the rollers travel along the grinding rings. Particles undergo repeated compression, impact, and grinding as they pass through successive layers. The number of layers and rollers varies by HGM model.

3. Dynamic air classification

Airflow carries the reduced particles toward the classifier. Particles fine enough for the selected cut point pass through; oversize particles are rejected and return to the grinding chamber. Classifier settings therefore affect both finished-powder fineness and the internal circulating load.

4. Powder collection and filtered exhaust

Qualified powder moves to the collection system and discharges for downstream handling or packing. A pulse bag filter captures residual airborne powder before the cleaned process air is released through the exhaust path.

Process line: Pre-crushing → Elevating and storage → Controlled feeding → Multi-layer grinding → Dynamic classification → Powder collection → Packing or downstream use

Clirik Ring Roller Mill

HGM Ultrafine Grinding Mill, Clirik's ring roller mill for fine and ultrafine mineral powder.

Broyeur ultrafin HGM

Clirik's HGM Ultrafine Grinding Mill is a ring roller mill for dry processing of brittle nonmetallic minerals. The series combines a multi-layer grinding chamber, adjustable air classification, powder collection, filtration, and line controls. Eight listed configurations let a project match the mill frame and drive system to the target powder and required production scale.

Manufacturer: Shanghai Clirik Machinery Co., Ltd.

Actual throughput and achievable particle size change with mineral composition, hardness, moisture, feed distribution, classifier configuration, and the required product cut point. A material test provides the operating basis for model selection.

Core specifications

• Taille maximale des aliments20 mm (0.79 in)
• Published output range5 to 100 μm (150 to 3,000 mesh), depending on configuration and material
• Material hardnessMohs hardness ≤ 6
• Material moisture≤ 6%
• Grinding layers3 or 4
• Roller count21 to 36
• Ring inner diameter800 to 1,680 mm (31.5 to 66.1 in)
• Main mill motor75 to 315 kW, depending on model
• HGM80 reference capacity0.5 to 5.5 metric tons per hour for calcium carbonate reference conditions

Request HGM Selection GuidanceView HGM Product Details

HGM Model Range: Structure, Drive Power, and Line Footprint

The HGM range scales from the three-layer HGM80 to four-layer machines with larger ring diameters and higher installed power. Models with the same ring diameter can still use different drive arrangements and line footprints, so the model suffix forms part of the equipment specification.

The structural table supports early space, power, and equipment screening. It also shows where a larger model changes civil layout and electrical demand before classifier settings and application-specific performance are considered.

Material Fit Starts With Hardness, Moisture, and Feed Size

HGM ring roller mills process dry, brittle, nonflammable, and nonexplosive feed within the stated hardness and moisture limits. Representative materials include calcium carbonate, calcite, marble, chalk, limestone, dolomite, gypsum, kaolin, bentonite, talc, mica, attapulgite, barite, phosphate rock, fluorite, carbon black, and graphite.

These powders can serve industries such as paint and coatings, paper, pigments, rubber, plastics and fillers, cable compounds, cosmetics, construction materials, and chemical processing. The required particle-size distribution depends on the downstream formulation, so two plants grinding the same mineral may need different classifier settings and mill configurations.

Select the Mill From Test Data, Not Mesh Alone

A useful selection brief connects the feed material to a measurable finished-powder requirement. State the mineral and composition, maximum feed size, hardness, moisture, required capacity, target particle-size distribution, available power, installation space, and the planned method for collecting or packing the powder.

Specify fineness with a particle-size value and distribution point, such as D97, whenever the downstream process depends on the coarse-particle limit. Mesh can remain as a familiar reference, but it does not fully describe the distribution that controls filler performance, coating behavior, or product consistency.

Clirik's material-testing workflow can include composition analysis, a grinding and classification trial, instrument measurement, test analysis, and configuration selection. The resulting data can establish achievable fineness, hourly output, and power demand for the submitted material before the production line is finalized.

A practical selection sequence

1. Define the feed properties and any safety constraints.
2. Set the required D97, capacity, and acceptable coarse fraction.
3. Run a representative material through grinding and classification tests.
4. Select the mill frame, classifier arrangement, collector, and auxiliary equipment from the test results.
5. Confirm line footprint, electrical load, interfaces, and packing method for the site.

What a Complete HGM Grinding Line Includes

An HGM project can extend beyond the mill body. The published system layout includes a crusher, bucket elevator, storage hopper, belt feeder, main mill, sound-control enclosure, classifier, powder collector, bag filter, muffler, blower, and electrical cabinet. The final equipment boundary depends on the incoming material condition and where the finished powder must go next.

Clirik provides grinding-line design, installation and commissioning, operator training, remote guidance, and on-site technical service. Wear-related components identified for the HGM series include the rollers, grinding rings, turn plate, shaft pins, and classifier impeller; spare-parts planning should follow the selected model and the abrasiveness of the actual feed.