Products

Aluminium hydroxide/ Al(OH)3 powder grinding mill

Aluminium hydroxide, Al(OH)3, ATH, sometimes erroneously called hydrate of alumina, is found in nature as the mineral gibbsite and its three, much more rare polymorphs: bayerite, doyleite and nordstrandite. Aluminium hydroxide/ Al(OH)3 powder grinding mill : five models: HGM80, HGM90, HGM100, HGM100A, and HGM125 finished production fineness: 300meshes~3000meshes, 5-47 micron the capacity (ton/hou

Over View
Features
Applications
Technical Data
Aluminium hydroxide, Al(OH)3, ATH, sometimes erroneously called hydrate of alumina, is found in nature as the mineral gibbsite and its three, much more rare polymorphs: bayerite, doyleite and nordstrandite.
 
Aluminium hydroxide/ Al(OH)3 powder grinding mill
—— five models: HGM80, HGM90, HGM100, HGM100A, and HGM125
——finished production fineness: 300meshes~3000meshes, 5-47 micron
——the capacity (ton/hour) ranges from 0.4T/H to 12T/H
 
Main Components of Aluminium hydroxide/ Al(OH)3 powder grinding mill:
HGM series Aluminium hydroxide/ Al(OH)3 powder grinding mill mainly consist of main unit, classifier, dust cleaner, powder collector, blower, muffler, hammer crusher (can be replaced by jaw crusher), bucket elevator, sound-proof room, storage hopper, vibrating feeder and so on.
 
Working Principle of Aluminium hydroxide/ Al(OH)3 powder grinding mill
●The crusher will crush the big materials into small ones, and then the elevator will send them to the hopper.
●The vibrating feeder will send the materials to the middle of first dial evenly.
●The motor of main equipment drives the main shaft and dial through reducer, and the dial drives numbers of rollers moving in the ring channels via pins.
●The materials will be driven to the edge of dial by centrifugal force and fall down into the ring, crushed and grinded by roller, and become powder after production of three rings.
●The high pressure centrifugal blower will inhale air from outside and bring the crushed materials to classifier.
●The rotating turbo in the powder collector will make the coarse materials return to the mill and regrounded, while the fineness will mix with the air and go into the cyclone and be discharged in the discharge bin, which is at the bottom of it.
●The air, which mixed with very little fineness, will be purified by impulse duster and discharged by blower and muffler.
 
Features of Aluminium hydroxide/ Al(OH)3 powder grinding mill:
● High Efficiency
Under the same finished final size and the same motor power, the capacity of Aluminium hydroxide/ Al(OH)3 powder grinding mill is twice as much as jet mill, mixing grinder and ball mill, and energy consumption decreased 30%.
● Long lifecycle of spare parts
The ring and roller are forged by special material with high utilization. Under the same grinding material and finish special size, the lifecycle of spare parts is about one year, which is 2-3 times longer than impact mill or turbo mill. Furthermore, the lifetime can reach 2-5 years for grinding calcite carbonate.
● High safety and reliability
As no rolling bearings or screws in grinding cavity, there are no problems caused by bolts shedding or rapid wear of bearings and seal components.
● High fineness, flexible adjustment
The final fineness of the grinding materials can be adjusted between 325 meshes and 2500 mesh (47-5 micron), and the product fineness can reach D97≤5μm.
●Environment-friendly
The application of pulse bag filter and muffler greatly alleviates dust pollution and noise.
●Advanced intelligent speed control device
Convenient adjusting, more uniform particle size.
Grinding mill is for super-fine grinding materials with hardness less than 6 in Moh‘s scale and humidity less than 6 percent such as kaolin, limestone, basalt, calcite, marble, talcum, barite, gypsum, dolomite, bentonite mud, mica, pyrophyllite, sepiolite, carbon black, diatomite, graphite, alunite, fluorite, potassium feldspar, phosphorite, pigment, up to 200 kinds. The granularity (or final size) of the finished products can be freely adjusted between 325-3000meshes (0.045-0.0057mm), and the capacity (ton/hour) ranges from 0.4T/H to 12T/H depending on the final size and the grinding.
Technical data of Aluminium hydroxide/ Al(OH)3 powder grinding mill:
 
Model HGM80 HGM90 HGM100 HGM100A HGM125
Ring Diameter(mm) 800 930 1035 1035 1300
Ring Number (PCS) 3 3-4 3 4 4
Roller Number(PCS) 21 24-32 27 34-36 40-44
Main Shaft Speed (r. p. min) 230-240 200-220 180-200 180-200 135-155
Input Size (mm) ≤20
Finished Size (um) 5-47(325-2500)
Capacity (t/h) 0.5-4.5 0.6-6.5 0.7-7 1-8.5 1.5-12
Outlet Size L*W*H (m) 13.9*4*6.2 14.7*4.8*7.2 18*4.6*8.6 18*4.6*8.6 14*9*10.25
Motor powder (KW) 145-165 185-204 263 263-290 380-430
 
Note: This specification is just referencing, any changes are subject to the products.

Need help? Live Chat

Top

FeedBack

Leave Us A Message ,We Will Contact With You As Soon As Possible

Name:

E-mail: *

Telephone:

Question:

Contact

For product information and pricing, Chat with sales agent:

or email us : sales@clirik.com

News Index

Click links below to see related products.